Beiträge von liftmys10

Zitat von Turboliner

Hello I have so to Wedico CAT 740 and I want to change to Faulhaber Engine My question is how does the engine shaft fit with the wedico gearbox? Is the Engine shaft from the Faulhaber Not to Short? Sincerely, Nick

Nick,
Nick,
You are right, the motor shaft is short when using the Premacon motor flange. However, you must use this flange to install the engine on the Wedico transmission. See pictures below.
Currently I do not like my setup. The 11mm original pinion is attached to the top of the motor shaft with the setscrew. The pinion also sits on 50% of the Wedico transmission. Again, I feel uncomfortable with my current setup. I wish premacon can make a longer sprocket with 12 teeth. Maybe 17mm long is perfect. ,

I have just scored on a 3557K012CR in new condition.
I resumed the standard Buehler engine at 6440 rpm and swapped it for the 5300 rpm 3557K012CR.

On my home test track, All, which is designed for 11' feet long on carpet, I ran in 1st, 2nd, 3rd and 3rd gear with 1 liter of water in bed on the floor.

I then swapped the engines and made the same average runs

Results
In first gear, the Bühler engine got 3.0 seconds faster
In second gear, the Bühler engine was 1.0 seconds faster
In third gear, the Bühler engine has the same speed as the 3557k012CR
3rd gear with 1 gallon of water in bed, the 3557k012CR is 0:10 seconds faster.

Conclusion:
On flat terrain without load, the Bühler engine has a higher top speed in 1st and 2nd gear, but both engines were equally fast in 3rd gear.
Where the 3557k012CR is loaded. In 3rd gear with no or 1 gallon of water, the speed was the same and did not change.
The Bühler engine slowed down considerably. I added the 1 gallon of water.
I will definitely enjoy the extra torque of the 3557k012cr and will spend more time in 2nd and 3rd gear while the Buhler was only the 1st and 2nd

Können die Organisatoren bestätigen, ob am 31. März eine Veranstaltung stattfindet?

Zitat von BaggerMartin

So, I would remove this Leimbach filter, that would be like trying to keep sugar with a noodle strainer. Everything that can damage the hydraulics goes through. Martin

Wenn der Leimbach-Filter nicht gut funktioniert, welchen Filter würden Sie empfehlen? Oder sagen Sie, dass Sie keinen Filter ausführen sollten, weil keiner von ihnen gut funktioniert?

woooooowwwww !!!
Beautiful photos! This is some of the best models I have seen in a thread. Thank you for sharing. Who makes the white color B40D? Fumotec?
I love the HD405!
What keeps more dirt? B35D or HM300?
Hat der B35D die gleiche Größe wie der B40D? Ich weiß, dass die 1: 1-Skala des b40d größer ist.

Okay, my first FPV video was taken by the camera directly above the cabin roof.
What I see through my Skyzone Sky02s is much better picture quality and in 3D compared to this 2D video I uploaded. The glasses make it much easier compared to this video. Hope that makes sense.
I'm getting better towards the end. I hope you like it!

From 3: 20-minute mark I clean the dirt for the CAT-740 landing site.

Mein erster Versuch mit der FPV-Brille Cat 740 zu laden. Überraschung bei 7:11 Minuten.

Toll aussehendes Modell mit gutem Geschmack in modifizierten Teilen. Ich wünschte, ich hätte die Mittel, die ich kaufen konnte, als Farhag verkaufte.

What has Leimbach done for service?

What type of hydraulic oil do you use and are recommended?

W:

Small update. I got a 6 volt version for the Faulhaber 3557k006c.
I will limit the speed through my radio so I will not turn the engine because I use a 3s lipo. I explain that in the video. I have to test with an actual load to see if it's better from the original machine.
https://youtu.be/nEnqP5FD0Y0

Zitat von maroehl

Does the engine of the WDC dump truck "wrong" on the 3-speed gearbox? As with the WDC wheel loader? If so, I am very interested in your solution for mounting a Fauli's !!! I've had a Faulhaber for my wheel loader, but since the Bühler engine, the sprocket only helped on the gear, I'm missing an idea to mount a Faulhaber with flange ...

Have you ever found a longer 12t sprocket? because the faulhaber with motor flange does not make the shaft long enough.

Great job! Amazing.

DX18 & x-plus 8... 100%

Hat jemand den LRP Truck Puller 3 12V Motor in wedico CAT verwendet?

Thank you!
3 variants to the Faulhaber 3557
C = 40 mNm
Cr = 80 mNm
Cs = 50 mNm

I do not know what the original Bühler engine compares, but it says 9.2 Ncm @ 2900 rpm

Is the CR version strongest? Will that be too strong for the cat740 or good?
Many thanks!

Hat jemand Erfahrung mit dem Einsatz von Premacon Motorflansch zur Montage eines LRP Truck Puller Motors oder Faulhaber 3557? Ich würde gerne mehr Leistung aus meiner wedico Cat 740 herausholen.
https://shop.premacon.com/product_info.php?products_id=187
Motor flange for Wedico gearbox. With this flange, the following engines can be mounted on a Wedico transmission: 3557r Lye, LRP Truckpuller, Robbe Truck and others with the same hole pattern

Schön! Ich liebe diesen alten Farbstil. Gute Arbeit!

Schön aussehender Lader! Herzliche Glückwünsche.