Wow! Thats a nice setup, looks soo scale!
Beiträge von KalleSwe
-
-
Very nice! Dont even look like a Bruder, super sweet!
-
Im impressed!
-
Really like your work, quick progress!
-
Looks like a great setup, im very impressed with your ideas and craftmanship!
-
That Liebherr looks so good, one of the better ones!
-
What an amazing build, love to see the updates from you!
-
Wow,, you work fast, you build it like its a kit!
-
Nice work, i really like the counterweight design!
-
-
Ahhh, PPM24!
-
Hello,
I have a MC19 with a XR-20 IFS reciver i can only use 9 of the 10 channels, if i try to assign a switch to the 10th chanel it wont react when i flip the switch, the reciver is brand new but the 10th channel wont work, what can that be?
Thanks
Kalle -
-
An little update on my excavator, i have now replaced the old undercarrige for the new drive for the tracks, what an difference in power, now i can go where i want to.
I have also added a auxillary extra hydraulics, almost finished, just need to paint the pipes, maybe i will replace the qucik connectros for the Liebherrmodelle ones, the ones on now are so huge, looks out of place.
The i have started a new quick coupler, all CNC:d from steel (not stainless), all internal parts are stainless, i have made 4 extra of them, they fit directly on the 470 or 870 excavators, they are driven by a micro geared motor with a motor controller from a 3 position switch, im still testing it to see how waterproof it is. Works good so far, i was digging in the snow yesterday for about 30min and i left it sitting in the garage over night to see if any rust would be in the cylinder holes, but no rust and it worked all good in and out.
Here is how the excavator looks now with the added parts...
-
Im going mad soon i think, i have done some testing this evening.
1. CTI module 1 in my excavator binds all good from the switch, i can
run it for about 30 secs to 3 minutes before my left track goes slower
in reverse, or the whole CTI unit shuts down.I have tryed a lot of things today, i have tryed different servos, i
thought maybe one servo was bad and messed up the binding, i tryed just
the tracks and pump to see if it worked, still the same thing.I also tryed without the CTI module, then everything works like it
should, i think i will throw the CTI module in the garbage can!2. CTI module 2 in my dumper, it only binds at times, sometimes first
try, sometimes i have to restart the radio and flip the switch and
repeat that until it binds, if i unplug the battery to my excavator the
dumper binds directly.This really makes me upset, i cant understand why it doesnt work, only
thing i can think of now is that my excavator reciver is bad and causing
the problem with my excavator, cant think of anything else.I cant understand why the excavator binds all good but the dumper does
not, only when the excavator is shut off the dumper will bind.I guess i have to get up and down in that damn chair this summer!
-
Hello Kalle
My englisch is not so good . I hope you understand me
Hott and ifs dont work together.Two Systems,it`s like 40Mhz and 2,4Ghz,it doesnt work too
ChristianOIk, i see, thankt for the help, i did understand your english just fine!
-
Hello,
Does the Hott GR-24 reciver work with the MC-19 IFS radio? Or do only the XR racivers work on that radio?
Thanks
Kalle -
Thanks guys!
sas: Only found small ones, need a little larger ones.
Martin: Those are very close, maybe i will get those.
Also found some at rc4wd that might be the deal.
Thanks for you replys!
-
Hello everyone,
Im looking for a scale lift hook like the one in the pic or similar, anyone know where to find one? Brass or steel.
-
Sorry, but why do you need "channel ONE"?
The modul is a pass-thru type. The opposite side of the input (cable from receiver) is the corresponding output.
Take one cable, put it into your receiver channel 3 (for example) and the opposite side (3-pin connector) is now channel 3.Ok, thanks for that, cleared things up for me!